Hello, KlausRoessler,

Please clarify whether you want to send such commands from the application or to receive a notification when a parameter is changed?

If you mean a notification about a parameter change, please specify the names of the parameters coming from the device, we will check it additionally. You can find these parameters in the Toolbox of your unit by looking at the messages.
More info about Toolbox you can find by the link. – https://help.gurtam.space/en/7af597c9-e302-4e55-a66d-9e9f97c67d93

    "SetBox is not available for devices in the “Legacy” category"……

    • rost replied to this.

      Hello, KlausRoessler ,

      Setbox is not available for devices in Legacy mode.
      However, try to use “Gosafe G1S” device type in unit settings. Then direct your device to new IP and port. This device type is from Hardware category and most likely has the same protocol as your device.
      Then check the unit’s Setbox. We do not guarantee that the commands will work, as the protocols may differ slightly, which may cause the commands to not work.

      We are planning to gradually add devices from the Legacy category to Hardware, but it will take time and for now you can try the method described above.

        Good day, unfortunately it doesn’t work with the settings of the Geosafe G1S. Do you have another solution? My commands + password at the end: time zone 896, coordinates 669, vibration 181 on 180 off alarm SMS when 12V ignition on 886

        • rost replied to this.

          KlausRoessler Hello,

          Please direct your device to our debug server:
          IP: 193.193.165.37 and port 29355.
          Then write to us, we will check it additionally.

            Good evening, thank you very much for your support. The Tracker is now online on your debug server. You can find the tracker with the ID 9171920685 or the IMEI 353130094365457

            • rost replied to this.

              KlausRoessler,

              We have verified the data from your tracker.
              The tracker connects but does not send anything, even the packet login does not come from the device, the device is immediately disconnected.
              In the package, even if the device does not have time to arrive, the device immediately terminates the connection.
              Please check your device configuration as we did not receive any complete data packet to check.

                Hello, after several attempts I got the tracker running again, it should now be available on the debug server under ID9171920685 or the IMEI

                Good day,

                For your information: I have just deactivated the test on the debug server and am connected to the portal normally again. If you want to analyze data again, please let me know. Best regards Klaus

                Good day,

                unfortunately Gosafe G1S does not work. But “MY Rilla G19” works immediately. For information: You have to register the tracker with the ID, IMEI does not work. Would it be possible to integrate this type into hardware?
                Thank you Klaus

                  KlausRoessler Hello!
                  Sorry for the long wait for an answer. Thank you for your help.
                  At the moment, according to the data received on the debug server and port, we saw that your device do not correspond to the protocol of Gosafe device from the Hardware category.
                  We plan to gradually integrate the most popular devices from the Legacy category and other popular devices in the Hardware category.
                  We will write to you when we come to the implementation of your device.

                    a month later

                    Hello, KlausRoessler

                    We are going to integrate the Sinotrack device protocol into our application.
                    Tell me, could you send us the documentation for this devices?

                    Also, maybe you will have the opportunity to send the device for tests?
                    If this is possible, please direct your devices to server 193.193.165.37 and port 23640.

                    If you have any documentation or can point a device, write to us from this forum thread.

                      I set up my ST 901 device to your server 193.193.165.37 and port 23640. I can keep it for several days. Device sends data at least every minute. Please write back if you receive messages. Unfortunately there is no device protocol description.

                      • rost replied to this.

                        Hello, MOHOMAX ,

                        Many thanks to you! We will check and answer you asap.
                        Please keep it connected for several days.

                          Sinotrack ST-901M connected to server 193.193.165.37 and port 23640. Id 9171770390

                          • rost replied to this.

                            Hello, andyworx, MOHOMAX

                            Many thanks! We see your units connected.
                            Please keep it connected for several days. We will notify you when we are done testing.

                                5 days later

                                Hello. Thanks, sinotrack 901m works fine in new hardware port, but in stock app im use external wire for blocking cars. Its work from button in stock app or sms commands. When external wire is activated, vehicle.state patametr in toolbox from FFFFFBFF change to F7FFFBFF. I would really like you to add the management of this feature in the ruhavik app in the future. Thx.

                                • rost replied to this.

                                  andyworx Hello,

                                  Please specify the name of the command, what is it called in the instructions for the device?
                                  Also, specify which SMS command corresponds to this command?
                                  This will help us to add commands.

                                  Thanks in advance!

                                    Hello, andyworx ,

                                    Yes, we can add such a command to Setbox.
                                    Do you have any documentation on the commands for this device?
                                    Also, we need a device to test. If the device is created in Ruhavik, tell me if you can provide a login and a time when we can test the command so that the device does not move.

                                    Thanks in advance!